-
-
-
Blog
-
Contact Us
What are the maintenance methods for a spiral sand-water separator?
Release time:
2022-09-06
What are the maintenance methods for a spiral sand and water separator? During daily use, pay attention to the noise of the spiral sand washer, observe the operation and working conditions of components such as the spiral shaft, V-belt, sealing device, and water pipe, check whether the motor and transmission system are overheating, and whether the bolts of various components are tightened. After 3-6 months of operation of the spiral sand flushing machine, the gearbox should be cleaned and replaced. So what are the maintenance methods for the spiral sand and water separator? What are the maintenance methods for the spiral sand and water separator? Large sand flushing equipment has reliable grounding devices for electrical equipment. In addition, the wires should be reliably insulated and installed in corrugated pipes. It is necessary to check the motor circuit for wear and leakage. To avoid accidents, seasonal maintenance of sand cleaning equipment is also important, mainly changing oil, fuel, antifreeze, and adding refrigeration facilities. In addition, if the spiral sand washer reaches its service life, it should be replaced in time, because as the spiral sand washer is used for a long time, the degree of aging is getting higher and higher, and the failure rate is also getting higher and higher, which not only affects the production efficiency of sand washing, but also increases the maintenance cost. As mentioned above, keeping in mind the maintenance methods of the spiral sand flushing machine arranged by Bian Xiao is essential to do this job well. Only by properly maintaining the spiral sand flushing equipment can mechanical failures be effectively reduced and the service life of the sand flushing machine be continuously extended.
Spiral sand and water separatorWhat are the maintenance methods?
During daily use, pay attention to the noise of the spiral sand washer, observe the operation and working conditions of parts such as the spiral shaft, V-belt, sealing device, and water pipe, check whether the motor and transmission system are overheated, and whether the bolts of each part are tightened. After the spiral sand separator runs for 3-6 months, the gearbox should be cleaned and replaced. So what are the maintenance methods for the spiral sand and water separator?
What are the maintenance methods for the spiral sand and water separator?
The electrical equipment of large sand washing equipment has reliable grounding devices. In addition, the wires should be reliably insulated and installed in corrugated pipes. It is necessary to check the motor circuit for wear and leakage. To avoid accidents, seasonal maintenance of sand cleaning equipment is also important, mainly changing oil, fuel, antifreeze, and adding refrigeration facilities.
In addition, if the spiral sand washer reaches its service life, it should be replaced in time, because as the spiral sand washer is used for a long time, the degree of aging is getting higher and higher, and the failure rate is also getting higher and higher, which not only affects the production efficiency of sand washing, but also increases the maintenance cost.
In summary, only by remembering the maintenance methods of the spiral sand separator arranged by Bian Xiao can this work be done well. Only by correctly maintaining the spiral sand equipment can the mechanical failures be effectively reduced and the service life of the sand separator be continuously extended.
Spiral sand and water separatorWhat are the precautions during maintenance?
1. If the thickness of the wear-resistant lining of the spiral sand and water separator is reduced to 5mm, it needs to be replaced.
2. Check and adjust the spiral connection status of the spiral sand and water separator every 1000 hours or 6 months.
3. Check the appearance and wear of the wear-resistant lining of the shaftless screw every two months.
4. The spiral sand and water separator is externally clean and hygienic, and the fasteners are firmly connected.
5. The reducer of the shaftless screw conveyor should be replaced every 16000 hours.
Quotation, Sales Hotline:0514-80913965 / 80913966
After-sales service:0514-80913977 / 80913979
Sales Hotline:0514-80913965 / 80913999
Technical Support:0514-80913952 / 80913953
Sales Fax:0514-80913999/86166402
Production base: Zhenwu Town, Jiangdu District, Yangzhou City, Jiangsu Province (Binhu)
Group Headquarters: Taishan East Road, Jiangdu District, Yangzhou City
Company E-mail:tianyugroup@vip.163.com
Sweep the attention to us